|
|
EDA365欢迎您登录！
您需要 登录 才可以下载或查看，没有帐号？注册
x
我在生成网表后，导入pads layout， 结果报告如下错误：
( U7 M& F% t+ w. J l1 @Can't find part Type item < XTAL_HC49SMT >+ X5 o: U# u" X/ j9 R% u
Y1 XTAL_HC49SMT2 l2 K# S3 {; e2 T0 b9 i5 e. d
Can't find part Type item < XTAL_HC49SMT >
- u6 R/ ^* c P4 eY2 XTAL_HC49SMT
( l% e. a6 U/ i2 D! hCan't find part Type item < XTAL_HC49SMT >
7 o# @* H$ U7 a# ? l* H- i$ _Y3 XTAL_HC49SMT6 |0 D$ n$ @8 a) T6 f K% Z
*Part name not found U13( V9 I6 Z* ]9 q9 p
U13.1 R9.1 C45.2 R13.2 R14.1
6 Q, n* `/ u$ H1 M: R- B; a*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N13564205 l" E9 l ]5 G
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal XT2_PHY
) x/ {& h3 s5 k( e! k*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_D+2
% K, D4 ?- d4 W) _5 T2 L' U4 k*Part name not found Y1 N. a, r' c1 m3 h$ v' `' u4 t
Y1.2 U6.1 C28.1 J3.1 J4.1 J5.16 Y& g+ s2 V' ]* P
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal OSC1' I: ~. n( p3 F" c' C& Y' G# s
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal CRS_PHY
; Y/ [+ [5 m, C& }* `4 d*Part name not found Y2# r) L! S" X, q) t' Z' V' J
U5.34 Y2.2 C41.2
3 `- I0 V% [- k, T6 g0 t3 f, h*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal RTCK1" c2 v- }2 P9 B
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal VDD_PHY
$ f+ \) S6 A/ Z) `*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal TXD1_PHY
& `8 J, w" ?5 i: }; x( Z*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_OTG_ID- I$ h% \9 V8 [3 r! ^" R$ d
除了上述报错元件不能导入，可以导入其它元件。我的部分PCB封装在自己建的pads库里，还用了些常用的自带库。请问
( P/ R" \% s+ u; h这些错是什么原因造成的？我看了一天了也没头绪。
/ S# H" m, w5 S3 d! g- `5 V* w多谢各位看完。
* ?1 j$ K+ i( L. x我会把整个设计放在附件里。
% P+ j0 \6 g, W; U; h3 Q3 n. }再谢。 |
|
/1 
发表于 2008-9-2 10:28
收藏
淘帖
支持！
反对！
楼主
我已经把封装改好了。