|
|
dbit 发表于 2011-10-1 21:44 ![]()
7 k" R8 k/ y4 _; ^你可以详细看一下DRC的说明再对症下药
4 Y$ ~$ Q* z' Q. c9 D. |6 x呀，终于有大侠明白我意思了。但是还是不懂怎么改。/ y4 f' {* _. x1 z% a1 z; M
错误如下。9 O, G3 ?& M. C3 [
< DRC ERROR >
# U) m# B: U1 T: M$ ~8 h" ^$ ?# O3 ] q* u3 S/ Q
Class: DRC ERROR CLASS8 }9 ?. i Q6 v( b6 q$ l
Subclass: BOTTOM0 _3 ^/ p( s7 P. }
Origin xy: (-833.54 -2264.18)% D9 z# y5 v) a. S5 f. y" Z, A
Constraint: Line to Thru Pin Spacing* R1 h. n) G& c% X" F+ D" v
Constraint Set: DEFAULT
. I8 k' ~: {$ A* y, p Constraint Type: NET SPACING CONSTRAINTS. X% B9 I/ J4 p+ N
! ]' x( q- y/ ?. j8 m Constraint value: 11 MIL* ~7 G4 Z/ z6 Q# s
Actual value: 0 MIL3 p p; y- L. t
( G+ f+ l: _3 M( l& U' I
- - - - - - - - - - - - - - - - - - - -
# U" t3 G3 c, p/ K Element type: SYMBOL PIN; N8 X# X/ k8 ~6 O- T! {
Class: PIN
% R) _3 d6 s; u3 b0 _8 y3 l, _7 A4 V& B
PIN: R26.2
J9 c3 Z' V A2 e3 `: n pinuse: UNSPEC2 O8 F9 t% A1 \
location-xy: (-856.52 -2287.16) + Z3 C/ I7 G7 l! ` F
part of net name: GND_SMALL_SIGNAL" L: p; q {4 Y$ ?
- - - - - - - - - - - - - - - - - - - -5 \/ B' z7 g; n: w) k/ S
Element type: ODD-ANGLE LINE SEGMENT
3 n6 N. R" c0 R) J Class: ETCH
2 W: u( N8 g0 l Subclass: BOTTOM# e5 p7 {$ v' A: i+ j& {% H- ]
. s) z3 t& @0 N2 O: W% J part of a connect line
) m& }# v6 P) t7 T3 r$ k3 J1 ~ Not on a Net
( T' p" B+ T A6 ^; C) b/ T1 j7 C7 ^8 ^1 @ U: S
) X6 a E6 Y0 Y% ~; f/ e% g: i. x我发觉错误的地方都是NOt on a Net。但我怎么修改导线的属性，令到它是我要的网络呢？例如我本来是模拟地，相连后，变了电源地，再改，模拟地就出错了，但电源地就无问题。求大侠指教 |
|
/1 
发表于 2011-10-1 15:31
收藏
淘帖
支持！
反对！
楼主