orcad library builder 16.6.62创建PCBfootprint库导出后没管焊盘管脚？

ylgw811002

在创建PCB footprint库导出时，没有焊盘不知道什么原因？如图所示，并出现下面提示：E- (SPMHAP-2): No padstack specified.E- (SPMHAP-3): Problem loading 'c45.pad'.; [; f) \- T! ~# \% F! @
8 A9 Y/ d) ~' l( vE- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
6 C- P, V$ z$ v: m( K+ t0 @E- (SPMHAP-2): No padstack specified.4 A) [6 B5 @6 ~& o, J0 r% D
E- (SPMHAP-3): Problem loading 'c45.pad'.: |7 l' m) @9 ]' K
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
9 ?) ^, k) P  n, b8 P4 A' G, ZE- (SPMHAP-2): No padstack specified.2 p3 \5 F$ c$ f" u+ I1 V
E- (SPMHAP-3): Problem loading 'c45.pad'.1 B) l# ~! d% X  E& V2 O
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.8 w/ I$ p2 s! f" f  I4 E
E- (SPMHAP-2): No padstack specified.! y3 Z/ p( v. P* A
E- (SPMHAP-3): Problem loading 'c45.pad'.+ k5 B: [8 `+ y# _" `
! o5 ^& m5 s) G4 z6 ?E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
E- (SPMHAP-2): No padstack specified.1 n/ b, r. c$ B9 y1 A7 E2 }7 x
E- (SPMHAP-3): Problem loading 'c45.pad'.
) t. i9 P$ l" Z/ ?E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.9 C$ x% y# Z$ Z' _2 x
E- (SPMHAP-2): No padstack specified.9 Y8 r5 K6 U# A2 _# F
+ n% \. a. \  {8 t% tE- (SPMHAP-3): Problem loading 'c45.pad'.: F7 H8 C6 t2 ?6 u3 Q5 i7 W
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.; S2 _5 t8 ^1 F4 I  P2 I2 e) O
0 y7 x3 x" O' U5 EE- (SPMHAP-2): No padstack specified.! W+ r! j/ e! b- [& b
E- (SPMHAP-3): Problem loading 'c45.pad'.* p) ]! r* U. z2 x( k1 H
) Y# p! e; X0 _8 R8 xE- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
' L3 M+ P% R9 F

ylgw811002

2 、在allegro中，软件默认的焊盘那些路径不能删除。即padpath路径下的$padpath不能给删除；出现此问题只和padpath路径有关系，和psmpath路径没有关系，路径设置如下（可以在原来的基础上添加其它路径）： 1

yangjinxing521

正解

TobyTao_Zhang

export libraries 之前先把要导出到 的folder 路径也加到padpath 里面

ylgw811002

为啥通孔类的没有焊盘了 擦  能否给个详细的教程

ylgw811002

能不能自动 DB doctor 生成的焊盘总是有问题

ylgw811002

能有大神给个解决的办法了 多谢了

liangping367

你能够导出OLB文件吗
! }( T) G- Q1 R2 d" ?

风凌天下

我的也是，问题我之前版本没问题，后面卸载重新装了就不能生成封装了