【PIC32 starter kit】之性能初窥

duzy

板载资源介绍
一．正面：
官方原文指导：
& O2 Z9 \+ u% N$ MThe top assembly of the board includes these key features, as indicated in Figure 1-1:
  G) ]6 {! f- V1.    PIC32MX795F512L 32-bit microcontroller (U2).   核心的东西
, n$ g& M- C& u2.    Green power indicator LED (D4).    电源指示灯
* v" b9 y. g9 F* u" W  _% F) G3.    On-board crystal for precision microcontroller clocking (8 MHz) (Y1). 板上晶振
/ |! o5 }* L3 N: I% G4.    USB connectivity for on-board debugger communications (J7).   小口USB连接器用于DEBUG
2 l! ~: O4 S" b' I5.    Debug indicator LED (D7).                 Debug指示灯
6.    Three push button switches for user-defined inputs (SW1, SW2, SW3). 3个按键，用户输入
" f+ N  L( J8 R' N' n6 L& D7.    Three user-defined indicator LEDs (D1, D2, D3).   3个用户指示灯
8.    USB Type A receptacle connectivity for PIC32 host-based applications (J4). USB连接器用于用户使用
9.    HOST mode power jumper (J5).   电源模式跳线
* @' e* l* ], |: V! R! w# N10.  LAN8740A PHY Daughter Board headers (J2)     这个拿到板的人一看就明白,网络连接接口
' I- u/ [  \) O( j- E; ]) H11.  50 MHz Ethernet PHY oscillator (Y3).  50MHZ晶振 没看文档前还以为是电容   
12.  32 kHz oscillator (optional) (Y2). 32KHZ晶振
13.  USB Host and OTG power supply for powering PIC32 USB applications (U4). 用户使用的USB工作芯片。
: R6 R, y$ F& D1 }二．反面：
/ J+ @% ^; q+ _% q& z! A1. Regulated +3.3V power supply for powering the starter kit through USB or
) k5 c/ h: T5 ?expansion board (U8).   3.3V的电源支撑
2.Connector for various expansion boards (J1).  扩展板连接器
1 s8 a, Z. T. x" f5 o9 E3.USB Type micro-AB receptacle for OTG and USB device connectivity for PIC32
OTG/device-based applications (J3).       OTG,micro-USB连接器
4.PIC24FJ256GB106 USB microcontroller for on-board debugging (U6).usb-debug芯片。
! S4 q8 B4 \. B1 P. a& L基本情况就介绍到这儿，这个板子本身所带的资源及信息。
0 D- R5 P/ d( q' K5 F1 a4 O
" m3 h/ q& m! a=======================================================================================================
三．性能及相关参数（捡主要的）
3.1 power supply
•  USB bus power connected to USB debug connector, J7.USB_debug连接器提供
( L* q3 Q: K4 V3 v•  An external application board with a regulated DC power supply that provides +5V  J1也就是板子背面最大的那个接扩展板的接口接供，暂不满足。
: N% @  E) [7 u3 N6 Ncan be connected to the J1 application board connector that is provided on the bottom side of the board.
3.2 PIC32 USB Connectivity（USB连接）
USB连接有3种模式，像大家最常用U盘，接到PC上，这种U盘就属于DEVICE MODE，PC就属于HOST MODE这种是大家最常用到的，
还有一种是OTG模式，
9 v( d" L* p; k8 r4 W* j2 p  T•HOST Mode – Connect the device to the Type A connector J4, located on the top side of the starter kit. If using the Debug USB port to power the Host port, install
# S. W" O6 q, t; |: xjumper J5 to short the back-power prevention diode. Note that a maximum of  ~400 mA can be supplied from the Debug USB port to the Host port using this method.
如果想要使用USB主机模式，那么必需就要接到J4上，也就是那个我们最常见的USB口上，如果是用MICRO-USB供电，则需要短接J5,也就是我们
在面板上看到的那两个排针。
' }& B( d$ ]1 X•DEVICE Mode – Connect the debug mini-B USB cable to port J7 and then connect the starter kit to the host using a cable with a Type-B micro-plug to the starter
kit’s micro-A/B port J3, located on the bottom side of the starter kit. The other end of the cable must have a Type-A plug. Connect it to a USB host. Jumper J5 should
! J/ H5 U( P" Z+ n# Obe removed.
7 \' J! E/ V* G  I* P: g/ T+ p2 i2 @DEBUG口，即是设备模式，但是需要将j7,跟J3都连接到电脑，J5也就是那个跳线需要断开。
5 l4 b% ?) x+ }8 Y7 X3 z•OTG Mode – Connect the starter kit to the OTG device using an OTG micro-A/B cable to the micro-A/B port J3, located on the bottom side of the starter kit. The
+ K0 f. }/ T9 m& Pstarter kit provides an on-board power supply capable of providing 120 mA Max. This supply is controlled by the PIC32MX795F512L microcontroller. Jumper J5 should
be removed.
只需要连接J3,但J5跳线要断开。

helendcany

哦，哦，哦，这个要记……

Haiting32451

学习了……