MY-IMX6-EK200 Linux-4.1.15 测试手册 v2.0（5）

thinkfunny

4  第四部分 扩展模块功能演示4.1  RTL8188 模块功能演示（WIFI Client）

【测试说明】：使用RTL8188作为无线网卡连接到WIFI AP。
【接口标识】：WIFI、WIFI_ANT
3 l6 Z3 }! C1 U3 [【系统设备】：wlan0
, X! [7 \! F6 p4 v9 J$ }) u测试操作
5 t- P7 R" k* H0 c7 U) F4 B; d1. 确定“WIFI”标识处有贴上WIFI模块，否则无需进行测试。
+ L$ H# Y6 m) l6 d! z2. 把WIFI天线连接到“WIFI_ANT”标识的接口上。
: O! c4 c% U# J- F3. 生成 SSID 的 WPA PSK 文件
命令格式: wpa_passphrase <ssid> [passphrase]

=====> 输入指令:

wpa_passphrase MY-TEST-AP myzr2012 > /etc/wpa_supplicant.conf

pkill wpa_supplicant

4. 连接

=====> 输入指令:

wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant.conf

=====> 输出信息：

Successfully initialized wpa_supplicant

RFkill: Cannot open RFKILL control device

==> rtl8188e_iol_efuse_patch

IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

......

5. 获取 IP

=====> 输入指令:

udhcpc -i wlan0

6 E" v5 h% q, R$ t# @( X

=====> 输出信息：

udhcpc (v1.23.1) started

Sending discover...

Sending select for 192.168.43.121...

Lease of 192.168.43.121 obtained, lease time 3600

/etc/udhcpc.d/50default: Adding DNS 192.168.43.1

6. 测试连接

=====> 输入指令:

ping -I wlan0 192.168.43.1 -c 2 -w 4

=====> 输出信息：

PING 192.168.43.1 (192.168.43.1) from 192.168.43.130 wlan0: 56(84) bytes of data.

64 bytes from 192.168.43.1: icmp_seq=1 ttl=64 time=5.66 ms

64 bytes from 192.168.43.1: icmp_seq=2 ttl=64 time=9.22 ms

--- 192.168.43.1 ping statistics ---

2 packets transmitted, 2 received, 0% packet loss, time 1000ms

rtt min/avg/max/mdev = 5.663/7.444/9.226/1.783 ms

测试结果
0 d( m% q! v0 S' h9 i1 T“0% packet loss”表示WIFI连接正常。

4.2  RTL8188 模块功能演示（WIFI AP mode）
* J% y$ h" N$ y/ H) s

【测试说明】：使用RTL8188作为WIFI AP，并把手机连接到此AP。
【接口标识】：WIFI、WIFI_ANT
【系统设备】：wlan0
: R3 C0 ~) ~8 h* |测试操作
1. 确定“WIFI”标识处有贴上WIFI模块，否则无需进行测试。
2. 把WIFI天线连接到“WIFI_ANT”标识的接口上。
3. 为 wlan0 配置 IP：

=====> 输入指令:

ifconfig wlan0 192.168.99.1

9 d5 T$ Z$ U/ T. D) m- \# H

=====> 输出信息：

==> rtl8188e_iol_efuse_patch

IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

4. 为 wlan0 启用 DHCP 服务：

=====> 输入指令:

touch /var/lib/misc/udhcpd.leases

udhcpd -f /etc/my_udhcpd.conf &

) K; l" t5 _9 m! @; Y, L' O

=====> 输出信息：

[1] 469

udhcpd (v1.23.1) started

5. 为 wlan0 启用 Host-AP 功能

=====> 输入指令:

hostapd /etc/my_hostapd.conf -B

=====> 输出信息：

Configuration file: /etc/my_hostapd.conf

rfkill: Cannot open RFKILL control device

Using interface wlan0 with hwaddr e0:b9:4d:7f:e4:40 and ssid "MY_HOSTAP_V25"

RTL871X: set group key camid:1, addr:00:00:00:00:00:00, kid:1, type:AES

wlan0: interface state UNINITIALIZED->ENABLED

wlan0: AP-ENABLED

6. 客户端设备连接到 Host-AP
至此，开发板的 Host-AP 功能已启用，客户端设备可搜索“MY_HOSTAP_V25”，通过密码“myzr2012”连接到此AP。
* |9 y, p4 m) @6 ^1 b测试结果
1 h" U4 I. I# S6 j+ z1. 设备连接成功时产生的信息

=====> 输出信息：

Sending OFFER of 192.168.12.20

Sending OFFER of 192.168.12.20

Sending ACK to 192.168.12.20

2. 设备断开连接时产生的信息

=====> 输出信息：

RTL871X: OnDeAuth(wlan0) reason=3, ta=b4:0b:44:f5:64:2f

RTL871X: clear key for addr:b4:0b:44:f5:64:2f, camid:4

4.3  EC20 模块测试

【测试说明】：4G连接成功后，开发板向外网发送ICMP报文来验证连接正常。
【接口标识】：MINI_PCIE
【系统设备】：eth2
测试操作
1. 开发板断电，接上4G模块，接上天线并插入SIM卡后启动评估板。
  n3 D  w5 m: w( i2. 使用指令进行网络连接：

=====> 输入指令:

/my-demo/gcc-linaro-5.3-ARM/quectel-CM &

=====> 输出信息：

[1] 540

[12-18_03:17:06:719] WCDMA<E_QConnectManager_Linux&Android_V1.1.34

[12-18_03:17:06:720] /my-demo/gcc-linaro-5.3-arm/quectel-CM profile[1] = (null)/(null)/(null)/0, pincode = (null)

[12-18_03:17:06:723] Find /sys/bus/usb/devices/1-1.2 idVendor=2c7c idProduct=0125

[12-18_03:17:06:723] Find /sys/bus/usb/devices/1-1.2:1.4/net/eth2

[12-18_03:17:06:723] Find usbnet_adapter = eth2

[12-18_03:17:06:723] Find /sys/bus/usb/devices/1-1.2:1.4/GobiQMI/qcqmi2

[12-18_03:17:06:724] Find qmichannel = /dev/qcqmi2

[12-18_03:17:06:794] Get clientWDS = 7

[12-18_03:17:06:826] Get clientDMS = 8

[12-18_03:17:06:858] Get clientNAS = 9

[12-18_03:17:06:890] Get clientUIM = 10

[12-18_03:17:06:922] Get clientWDA = 11

[12-18_03:17:06:954] requestBaseBandVersion EC20CEFAR02A10M4G

[12-18_03:17:07:050] requestGetSIMStatus SIMStatus: SIM_READY

[12-18_03:17:07:082] requestGetProfile[1] cmnet///0

[12-18_03:17:07:114] requestRegistrationState2 MCC: 460, MNC: 0, PS: Attached, DataCap: LTE

[12-18_03:17:07:146] requestQueryDataCall IPv4ConnectionStatus: DISCONNECTED

[12-18_03:17:07:223] requestRegistrationState2 MCC: 460, MNC: 0, PS: Attached, DataCap: LTE

[12-18_03:17:07:274] requestSetupDataCall WdsConnectionIPv4Handle: 0x8777e7a0

[12-18_03:17:07:370] requestQueryDataCall IPv4ConnectionStatus: CONNECTED

[12-18_03:17:07:403] ifconfig eth2 up

[12-18_03:17:07:452] busybox udhcpc -f -n -q -t 5 -i eth2

[12-18_03:17:07:492] udhcpc (v1.23.1) started

[12-18_03:17:07:656] Sending discover...

[12-18_03:17:07:706] Sending select for 10.25.154.46...

[12-18_03:17:07:766] Lease of 10.25.154.46 obtained, lease time 7200

[12-18_03:17:07:888] /etc/udhcpc.d/50default: Adding DNS 211.136.17.107

[12-18_03:17:07:888] /etc/udhcpc.d/50default: Adding DNS 211.136.20.203

3. 测试连接

=====> 输入指令:

ping -I eth2 www.baidu.com -c 2 -w 4

6 c7 V/ u5 g2 _  G

=====> 输出信息：

PING www.baidu.com (14.215.177.38): 56 data bytes

64 bytes from 14.215.177.38: seq=0 ttl=49 time=15.753 ms

64 bytes from 14.215.177.38: seq=1 ttl=49 time=11.835 ms

--- www.baidu.com ping statistics ---

2 packets transmitted, 2 packets received, 0% packet loss

round-trip min/avg/max = 11.835/13.794/15.753 ms

测试结果
& v7 ?$ E  H! a3 b# L9 ~. P( B“0% packet loss”表示WIFI连接正常。

/ Z4 C$ i7 j) A2 l

gaoxings

学习一下，谢谢楼主分享