|
|
EDA365欢迎您登录！
您需要 登录 才可以下载或查看，没有帐号？注册
x
我在生成网表后，导入pads layout， 结果报告如下错误：
2 x7 b0 c$ v/ i6 A" eCan't find part Type item < XTAL_HC49SMT >
! B- Y! t1 o/ l. T2 j# }+ xY1 XTAL_HC49SMT
3 W7 B2 y( S9 lCan't find part Type item < XTAL_HC49SMT >; q$ o$ T3 C0 I
Y2 XTAL_HC49SMT
4 E9 p! }. H! |" _, e6 Z+ e- t* ~Can't find part Type item < XTAL_HC49SMT >0 l P2 I) `" T! l X
Y3 XTAL_HC49SMT
- Z( f8 I8 z2 N3 c) j0 U*Part name not found U137 l, @2 L0 g# F- j
U13.1 R9.1 C45.2 R13.2 R14.1; n0 n0 }5 l* u% H3 h
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N1356420
* T% D$ K, ?/ }+ J0 q) k+ T. W% y- C*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal XT2_PHY
" J1 ?! ^1 ]' ?( C*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_D+2* L* t* W/ [) e* ~' d! a8 x
*Part name not found Y1
9 a* g9 G2 G% W9 u& OY1.2 U6.1 C28.1 J3.1 J4.1 J5.16 b' L n- L T$ Q" M9 g% i* o
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal OSC1! V Q1 e4 m. U/ }! r, j' M5 J
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal CRS_PHY2 ?, L0 m. A% ^+ M8 z
*Part name not found Y20 N$ ^/ h" R5 h4 m
U5.34 Y2.2 C41.20 V- c3 @$ c/ g# N9 [/ e
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal RTCK1
% d, D1 p A% E2 k*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal VDD_PHY t7 u! ] n& G% x t: e
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal TXD1_PHY' g9 F: L. g. B# F4 ?2 W; b
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_OTG_ID
3 n: F+ O# G" O; m除了上述报错元件不能导入，可以导入其它元件。我的部分PCB封装在自己建的pads库里，还用了些常用的自带库。请问4 @3 s+ Y, x6 g1 N$ C* p7 r4 n( h
这些错是什么原因造成的？我看了一天了也没头绪。
" m% ?" L& c- J2 B多谢各位看完。
9 i q. Q3 p3 n7 z我会把整个设计放在附件里。2 _6 L+ s: i8 y; E2 T! I
再谢。 |
|
/1 
发表于 2008-9-2 10:28
收藏
淘帖
支持！
反对！
楼主
我已经把封装改好了。