|
|
EDA365欢迎您登录！
您需要 登录 才可以下载或查看，没有帐号？注册
x
我在生成网表后，导入pads layout， 结果报告如下错误：
7 X2 [( g( R$ }- NCan't find part Type item < XTAL_HC49SMT >- K; W/ t+ R1 o5 t# \6 \1 m9 w
Y1 XTAL_HC49SMT4 v( N0 x1 C; m& P
Can't find part Type item < XTAL_HC49SMT >% ~- V2 K2 h$ p) g; n0 n' g5 o9 @1 r
Y2 XTAL_HC49SMT
0 B2 L: {8 H! d, I i+ fCan't find part Type item < XTAL_HC49SMT >
$ ?3 I ^* u) Y. w) @Y3 XTAL_HC49SMT9 g8 ~" O+ s, l3 e1 h
*Part name not found U13
# w# P- c3 r5 T) d6 v2 wU13.1 R9.1 C45.2 R13.2 R14.1
, v* e5 U, V5 r*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N1356420, W2 X; X. }$ n; P3 h7 P- ?
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal XT2_PHY
$ o+ d& u& E) Y& T*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_D+2* U# s" f; h# s6 B+ e# X: _" F+ ?7 R
*Part name not found Y1
3 Y7 A3 V+ q0 l7 y4 |; N' `. AY1.2 U6.1 C28.1 J3.1 J4.1 J5.1
9 Q: y0 o6 e9 w" f! M: [, U% u*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal OSC1
2 ?! o& d5 x6 H, t*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal CRS_PHY$ m$ V7 |2 A" ?
*Part name not found Y29 h( O: E$ m5 B/ J' ]' D' [
U5.34 Y2.2 C41.2$ o3 i) I& b, p9 T0 r4 I: h8 S# g1 |
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal RTCK1) c' Z& \% |# \
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal VDD_PHY
6 u+ ~4 R; L& D& R*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal TXD1_PHY
5 `5 L8 p+ B& I# o+ ~4 N3 b*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_OTG_ID
" }; Q# C7 y3 W5 ]& ], a- d除了上述报错元件不能导入，可以导入其它元件。我的部分PCB封装在自己建的pads库里，还用了些常用的自带库。请问1 l$ h( |7 O& d l+ L
这些错是什么原因造成的？我看了一天了也没头绪。
( F+ K Q2 k1 E3 j多谢各位看完。* U b, d( y0 `3 _' h& R3 x
我会把整个设计放在附件里。1 a; V6 P& ], R+ G
再谢。 |
|
/1 
发表于 2008-9-2 10:28
收藏
淘帖
支持！
反对！
楼主
我已经把封装改好了。