|
|
EDA365欢迎您登录！
您需要 登录 才可以下载或查看，没有帐号？注册
x
我在生成网表后，导入pads layout， 结果报告如下错误：5 ?/ H. F5 G D7 ]& W0 v
Can't find part Type item < XTAL_HC49SMT >. ~) t, K% R8 r
Y1 XTAL_HC49SMT- S3 [+ P, h) @$ r3 S/ m
Can't find part Type item < XTAL_HC49SMT >0 m# w2 {' p4 z3 ~, v
Y2 XTAL_HC49SMT) q1 h$ W/ w8 ^# @' I
Can't find part Type item < XTAL_HC49SMT >
6 o5 n. Y- O4 t' L9 r8 {; J$ ?Y3 XTAL_HC49SMT
% L6 N8 P/ e, D) x0 y*Part name not found U13
# p& e% R, ?. e4 @U13.1 R9.1 C45.2 R13.2 R14.1
3 \ E/ T! P; A6 t*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N1356420. n c& Y9 \: q. x1 L( [
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal XT2_PHY" F- H9 P- f# F. \/ \6 \
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_D+2
5 c3 s- M! d* ~, I3 o5 ?( L*Part name not found Y1
$ S6 Z, Z, l4 z. U- e8 O& FY1.2 U6.1 C28.1 J3.1 J4.1 J5.1
5 ^* Y0 ]6 E; w& Y4 I0 e! B( f*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal OSC1- y7 ^" @2 |- `5 |
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal CRS_PHY: C* G# a0 Q" E2 N* z8 M! `. m
*Part name not found Y2
/ H, U; t" t" RU5.34 Y2.2 C41.2. i2 z4 W5 g" x1 H
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal RTCK1
6 `+ J1 k1 |+ n+ l& s2 [*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal VDD_PHY8 I: i' G1 A( a' L8 x
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal TXD1_PHY
% r- ~' D0 u" u7 P: O*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal USB_OTG_ID* h8 P1 T6 M. ~+ c
除了上述报错元件不能导入，可以导入其它元件。我的部分PCB封装在自己建的pads库里，还用了些常用的自带库。请问) f- C4 r$ Z$ G5 I* ]; Q
这些错是什么原因造成的？我看了一天了也没头绪。
, q5 G6 V. |( v6 _多谢各位看完。1 M. R8 {5 z' P+ i( }4 V; E3 T1 k
我会把整个设计放在附件里。8 }: _9 m4 W; p
再谢。 |
|
/1 
发表于 2008-9-2 10:28
收藏
淘帖
支持！
反对！
楼主
我已经把封装改好了。