IBIS在Mode Integrity中出现了如下错误

xiaochaoaction

WARNING (line  433) - Pulldown Maximum data is non-monotonic
; }) z+ `8 b8 n1 `4 zWARNING (line  434) - Pulldown Typical data is non-monotonic
WARNING (line  435) - Pulldown Minimum data is non-monotonic
WARNING (line  609) - Pullup Maximum data is non-monotonic
WARNING (line  610) - Pullup Typical data is non-monotonic
WARNING (line  610) - Pullup Minimum data is non-monotonic
WARNING (line 1028) - Pulldown Maximum data is non-monotonic
1 x1 J7 Q  X, e" g7 jWARNING (line 1029) - Pulldown Typical data is non-monotonic
8 v5 _* B, `' Z) r# ?WARNING (line 1030) - Pulldown Minimum data is non-monotonic
3 E7 b! X9 ]2 V* R( wWARNING (line 1535) - Pulldown Maximum data is non-monotonic
% G5 p1 k8 |% A2 l( sWARNING (line 1536) - Pulldown Typical data is non-monotonic
& Z7 U( j: t* P# n4 X1 r1 u0 ~WARNING (line 1537) - Pulldown Minimum data is non-monotonic
WARNING (line 1717) - GND Clamp Minimum data is non-monotonic
0 K* e  P: O1 B% p: kWARNING (line 1890) - POWER Clamp Minimum data is non-monotonic
* |6 `8 ]7 J5 w' k. x: w8 `% w6 z! MWARNING - Model 'DBX_B06060B0S2AKZGBE': Vmeas timing test load parameter should be specified
WARNING (line 1944) - Pulldown Maximum data is non-monotonic
WARNING (line 1945) - Pulldown Typical data is non-monotonic
- @2 n# N: V1 [! e0 f- yWARNING (line 1946) - Pulldown Minimum data is non-monotonic
8 M5 s1 v& d; h5 f$ Q; K/ HWARNING (line 2153) - Pullup Maximum data is non-monotonic
WARNING (line 2154) - Pullup Typical data is non-monotonic
) y% n1 }4 u* ^3 i$ U' A% GWARNING (line 2154) - Pullup Minimum data is non-monotonic
6 A, h0 q# {; b. G5 eWARNING - Model 'DBX_B08081B0S2ALZGIE': Vmeas timing test load parameter should be specified
- b# Y( d9 c& K4 z+ C: @WARNING - [Model] DBX_D00200B0S2AZZGHE has no description of the buffer's high state
         DC drive characteristics (no [Pullup] table).  This warning
! g+ R" n2 k" Z( G         can be silenced by using an open drain Model_type or by
         adding a [Pullup] table.
8 s3 n  i, M+ P& S6 \8 }$ _( ]
谁能帮忙解决一下，谢了。。。

xiaochaoaction

xiaochaoaction

yoyof3 发表于 2012-8-5 22:58
9 E8 b' o; k8 X. i8 q警告可以不管，把错误处理完就可以了。

0 T+ F' {4 [2 u7 \- z7 V1 T# g谢谢{:soso_e100:}

yoyof3

警告可以不管，把错误处理完就可以了。

pwj6323

无法修改。呵呵。。{:soso_e100:}

procomm1722

這個不用理會