layout使用的时候出现错误

shuiye

在布线的时候删除一些过孔布线的时候会出现以下问题：
/ V6 I; x7 z1 Z( k( d
然后就关闭了。
7 F# q' }, Q: g( `* k  Y$ _我按照网上搜寻的方法把PCB导出成ASC文件，再新建PCB导入ASC文件，但是导入的时候又出现了一个问题：

6 }; j, g* _+ O7 B3 |# n并且有一个文档提示，内容如下：
( i7 `# @3 y3 O- k0 f*Duplicate level definition in pad stack -1
+ p. F- ]( f4 l8 a  f7 S-1 3238500 OF  0.000 4572000 0  
Too many decimal places in number
! p  f6 d+ b, \5 Y% d5 [9 O-1 2476500 ST  0.000 3238500 762000 4
7 _$ ^3 u) ]* E+ v6 S  x7 f( M/ ~*Bad *PARTDECAL* ascii data line format
' }/ W0 H" m3 H+ M0  2667000 OF  0.000 4191000 0  
4 Q+ ?4 `5 E6 {0 m* n*Bad *PARTDECAL* ascii data line format
121 2895600 OF  0.000 4419600 0  
7 Z2 C  Y/ e2 ]5 }*Bad *PARTDECAL* ascii data line format
1 ?4 L" g4 n$ f6 S1 U0 E128 2895600 OF  0.000 4419600 0  
*Bad *PARTDECAL* ascii data line format
PAD 13 7
5 f1 m; Y4 V% }, P5 K, PToo many decimal places in number
-2 2667000 OF  0.000 4191000 0   1714500 P 0.000 3048000 0  
4 C) X# @( d+ x# O. b! b# u& ~2 U*Bad *PARTDECAL* ascii data line format
2 t5 V  T; Q  P9 C-1 2667000 OF  0.000 4191000 0  
*Bad *PARTDECAL* ascii data line format
. _  E9 F5 c2 k-1 3238500 OF  0.000 4572000 0  
8 X) s$ o5 \' D: p( kToo many decimal places in number
-1 2476500 ST  0.000 3238500 762000 4
% I2 Q' M2 t* G) F; W, C+ l% N0 I4 o*Bad *PARTDECAL* ascii data line format
3 ]! ~9 n% U1 J/ A4 p4 g6 ]9 M" f0  2667000 OF  0.000 4191000 0  
*Bad *PARTDECAL* ascii data line format
121 2895600 OF  0.000 4419600 0  
1 p4 {/ B3 {/ b2 ~0 h9 T6 w" }! i+ w*Bad *PARTDECAL* ascii data line format
" g2 S/ Z2 ]  I) N4 D128 2895600 OF  0.000 4419600 0  
( f" z" X% s. r3 ^" z+ Z( G7 e7 G*Bad *PARTDECAL* ascii data line format
PAD 14 7
Too many decimal places in number
-2 2667000 OF  0.000 4191000 0   1714500 P 0.000 3048000 0  
: C/ \1 Z8 f9 ]& ^, `*Bad *PARTDECAL* ascii data line format
0 F8 \3 s: X3 N6 L2 c) e-1 2667000 OF  0.000 4191000 0  
! v6 Z3 z/ Q# u7 {*Bad *PARTDECAL* ascii data line format
( H3 a) q# j4 i% Y! _-1 3238500 OF  0.000 4572000 0  
. Q5 i% D! o5 H  E! VToo many decimal places in number
0 p. w$ \' i% C; W. ]-1 2476500 ST  0.000 3238500 762000 4
; J8 j) U8 Z, f- @4 C. r9 ^, X+ _*Bad *PARTDECAL* ascii data line format
0  2667000 OF  0.000 4191000 0  
0 e& K, u5 q7 n6 A0 |4 E*Bad *PARTDECAL* ascii data line format
9 u) v6 x* J! ]! B$ J- Q121 2895600 OF  0.000 4419600 0  
; P$ S* g. t: u3 y$ E*Bad *PARTDECAL* ascii data line format
128 2895600 OF  0.000 4419600 0  
7 p' C9 Q: t9 l* }8 u2 c4 F*Bad *PARTDECAL* ascii data line format
' Z  g* t6 ^3 N8 BPAD 15 7
这个问题怎么解决呢?
$ W  @+ w) I8 O3 O* A7 y7 d