大家帮我看一下仿真的问题 ？？

xiaowenwu1989

   如附档图，我仿真时出现一个这样的对话框，请问一下我应该怎样弄呢？

wwddss_1976

9 s$ D* ~- M' H4 R6 t) ]把相应库文件添加到nom.lib所在位置

xiaowenwu1989

xiaowenwu1989 发表于 2016-10-21 09:39

# N" v  N: x" j& j3 l大神们怎么弄
! h/ G: |1 w; j' O6 A: B
1 l$ ]$ d% j; V  D+ k3 N

xiaowenwu1989

wwddss_1976 发表于 2016-10-20 18:21
Can't find library，没有把相关库添加进去

- J) }! _# R8 m! h& x* u

xiaowenwu1989

wwddss_1976 发表于 2016-10-20 18:21
: B  Q$ k, _. k" A! C" |: g9 ZCan't find library，没有把相关库添加进去

0 V8 t) Y0 C+ _   哥你帮我看一下，我不知道怎么弄
- @1 G/ X! `( u& p' u: _
6 r# F8 g/ G' }& b2 F0 b% |
Creating PSpice Netlist
INFO(ORNET-1041): Writing PSpice Flat Netlist D:\CADENCE\SPB_16.6\TOOLS\CAPTURE\test123-PSpiceFiles\SCHEMATIC1\SCHEMATIC1.net
. D" x  v6 b& H' t0 u+ oINFO(ORNET-1169): Unable to open the property mapping file: devparam.txt. To resolve this problem, ensure that PSpice.ini exists at the correct location. After that check Library Path in simulation settings contains <installation-path>/tools/pspice/library path and then create the netlist again.
5 J, G( H6 T7 J& Q& r6 XINFO(ORNET-1162): Unable to create design property file.

+ j# U! V' y- z
; e. V% |/ t. ^4 \0 e( A

wwddss_1976

Can't find library，没有把相关库添加进去

xiaowenwu1989

wwddss_1976 发表于 2016-10-19 20:22
查看session log

# K( W' i' q! G) _就看到一个这样的东东：
  v& c3 s) n. `0 E5 P& s1 n**** 10/19/16 15:28:12 ***** PSpice 16.6.0 (October 2012) ***** ID# 0 ********

** Profile: "SCHEMATIC1-test123"  [ D:\CADENCE\SPB_16.6\SPB_DATA\test123-PSpiceFiles\SCHEMATIC1\test123.sim ]
- F& L6 F, Q/ _" ]; \3 ]

****     CIRCUIT DESCRIPTION
. F6 e+ C2 ?% h" U
$ B. d; |' i& e. ~9 b
******************************************************************************


% N: ?9 f1 r4 d% o6 x

, C0 H4 Z1 @( a) D* H** Creating circuit file "test123.cir"
. h0 _2 i5 o. W2 Q** WARNING: THIS AUTOMATICALLY GENERATED FILE MAY BE OVERWRITTEN BY SUBSEQUENT SIMULATIONS

*Libraries:
* Profile Libraries :
* Local Libraries :
* From [PSPICE NETLIST] section of C:\DOCUME~1\XIAOWE~1\LOCALS~1\Temp\16.6.0/PSpice.ini file:
( P" }, E/ `9 H* m4 \# K& B.lib "nom.lib"
- w% i6 a3 z, z' [# Y
! d  ?& g: A0 u; h& F*Analysis directives:
---------------$
0 w# L: Q  \8 ]! Y& OERROR(ORPSIM-16276): Can't find library
.TRAN  0 1000ns 0
.OPTIONS ADVCONV
.PROBE64 V(alias(*)) I(alias(*)) W(alias(*)) D(alias(*)) NOISE(alias(*))
8 V% H% X  ^8 U8 u& Q4 y.INC "..\SCHEMATIC1.net"
+ X: r' k/ t  |0 @4 y

  Q" F/ v. V' O0 ^  w4 Q. A. H
**** INCLUDING SCHEMATIC1.net ****

5 Q. K& D/ `$ D9 d+ R+ N6 l4 x" D) m**** RESUMING test123.cir ****
" p4 G( U* g! O- ^: ]; @# O.END
2 F8 U! J/ u! l
: |8 G/ o# K) K

jacklee_47pn

貌似圖片中紅色框框中沒打點(沒連接上)。導致三極管 E 極沒連上。

wwddss_1976

查看session log