|
|
EDA365欢迎您登录！
您需要 登录 才可以下载或查看，没有帐号？注册
x
本帖最后由 buptdlmuzbx 于 2011-4-20 16:45 编辑 * e3 I( u- `5 q H# ~
$ G8 j" f2 r- A! U, W, KSUMMARY:
7 C; U, a7 v0 Q3 l TOP created with warnings
0 @+ G! Q" d; j GND created with warnings
5 e! _/ ~ v1 r* F' |5 ]( Z VCC created with warnings
; |! Y6 C! d, P5 t6 d6 V1 ?3 ` BOTTOM created.. w c; E/ Z) v& B6 B# g) [" T
SILKSCREEN_TOP created with warnings; C9 q+ y6 v$ x& {0 ]
SILKSCREEN_BOTTOM created.
; {: W- H, |- V. Q SOLDERMASK_TOP created.
* [% }1 z& Q& O' ?* D SOLDERMASK_BOTTOM created.( {+ o- J" l! ?% P
PASTEMASK_TOP created.
: c; p) h. M4 p, c) y- Q( T8 d1 V PASTEMASK_BOTTOM created./ u' {( }6 u/ M% U; V/ o
OUTLINE created.
( W$ K4 l+ P- w/ M DRILL created.$ d! U- a! `0 s/ w) C# Q
ARTWORK finished
$ a3 t: W) B% X, F这是最后的结果，
! C7 M6 q: g- ?# V% Y我想问下既然光绘finished，那这些warning能忽略吗？
: m: E* Q& P. X) Y3 @1 IWARNING: 0 width line found at (0.0000 0.6350)
' _2 W0 N; L ]6 y/ b ... using undefined line width of 0.1524
( c6 z# N+ w1 l1 z( h7 T& R& TWARNING: Multiple 0 width lines; all will be treated the same as the first.
% V( j' g0 s) S. o v ... using undefined line width of 0.1524
7 V q- t" j8 B WARNING: No Photoplot Outline was found,
) ]" ]2 V+ i5 q8 A- q1 x: \negative shape outline will be determined by Board Outline
8 F7 M8 w, P |) G& z" d WARNING: No Photoplot Outline was found,
. Z' U! w2 P# b. @, p: W* k* Lnegative shape outline will be determined by Board Outline
& }4 o- [" ~3 K- U8 |- CWARNING: text composed 0 width line found at (9.7282 5.5626)
r$ [* i5 W7 n# c- h4 `' K+ \8 y1 a ... using undefined line width of 0.1524/ a+ I3 H/ _0 E/ e/ o" [8 y
WARNING: text having Multiple 0 width lines; all will be treated the same as the first.: T) }/ A8 T9 \1 ], r& M/ ?& s
... using undefined line width of 0.15245 R1 |. x; s, k$ f9 Z; t* Z9 }/ D
* G2 e6 s9 y' S' p2 @" J8 O, P) [+ t/ `
这是什么呀！谁能给解决下！有木有！有木有！
, s% `6 J5 X- q9 F' V |
|
/1 
发表于 2011-4-20 16:30
收藏
淘帖
支持！
反对！
請問您是不是有SHAPE做的零件超出板框了呢？