GPRS模块SIM300的使用

uqHZau · 发表于 2020-3-27 10:32

EDA365欢迎您登录！

您需要登录才可以下载或查看，没有帐号？注册

x

GPRS模块使用的说明
使用GPRS首先需要打开串口，设置好串口的各项参数。

一、AT+CMGL 读取所有短信
A、读取所有的信息：

第一步：at+cmgf=1 如果返回ok则继续。

说明：AT+CMGF  SELECT SMS MESSAGE FORMAT

第二步：at+cmgl=”all”

成功返回OK否则ERROR

+CMGL: 1,"REC READ","+8613702936376",,"05/12/16,09:04:43+00"

test

OK

B、读取未读的信息

第一步：at+cmgf=1

如果返回ok则继续。

第二步：at+cmgl=” rec unread”

成功返回OK否则ERROR

C、读取已读的信息

第一步：at+cmgf=1

如果返回ok则继续。

第二步：at+cmgl=” rec read”

成功返回OK否则ERROR

AT+CMGL参数：

1) If text mode:

  "REC UNREAD" Received unread messages (default)

  "REC READ"       Received read messages

  "STO UNSENT"    Stored unsent messages

  "STO SENT"          Stored sent messages

  "ALL"                   All messages

2) If PDU mode:

  0       Received unread messages (default)

  1       Received read messages

  2       Stored unsent messages

  3       Stored sent messages

  4       All messages

二、AT+CMGR Read SMS message
从X存储区读短消息:

   第一步：at+cmgf=1 如果返回ok则继续。

   第二步：at+cmgl=x

三、AT+CMGD Delete SMS message
删除信息：

   第一步：at+cmgf=1

                  如果返回ok则继续。

   第二步：at+cmgd= 数字号

成功返回OK否则ERROR

四、AT+CSCA SMS service centre address（设置短信中心号码）
设置短信中心号码：

   第一步：at+cmgf=1

                  如果返回ok则继续。

   第二步：at+csca=”短信中心号码”  （比如+8613800546500）

                  成功返回OK否则ERROR

五、AT+CMGS Send SMS message (发送信息)
发送信息：

   第一步：at+cmgf=1

                  如果返回ok则继续。

   第二步：AT+CMGS=“+8613xxxxxxxxx”<回车>

>输入短消息。Crtl+Z结束并发送。

注：此只能发送英文与数字

六、查询
查询设备：

命令：AT+CGMI<回车>

返回：SIEMENS

返回：OK

命令：AT+CGMM<回车>

返回：MC35i

返回：OK

命令：AT+CMEE=1<回车>

返回：具体的错误代码

ATZ;E 回车 Echo OFF

ATZ;E1回车 Echo ON

AT+CREG？回车回答x(X=2脱网，X=1注册，X=0状态不明)

AT+COPS？回车表示SIM卡是否被网络接受

AT+COPS=?回车显示所有可用的网络。

AT+CREG？回车(是否网络注册)

AT+CSQ    SIGNAL QUALITY REPORT

AT+IPR=2400 回车(改变RS232口的速率至2400bps)

AT&W 回车 (保存已改参数)

输入PIN码：AT+CPIN=“xxxx”

七、网络是否注册（AT+CREG?）
命令：at+cmgf=1

返回：at+cmgf=1 返回：OK

命令：AT+CREG?

返回：AT+CREG? 返回：+CREG: 0,1

注：( 2脱网， 1注册， 0状态不明)

返回：OK

八、SIM卡是否被网络接受（AT+COPS？）
命令：at+cmgf=1

返回：at+cmgf=1

返回：OK

命令：at+cops?

返回：+COPS: 0,0,"China Mobile"

返回：OK

九、显示所有可用的网络（AT+COPS=？）
命令：at+cmgf=1

返回：at+cmgf=1

返回：OK

命令：at+cops=?

返回：+COPS: (2,"China Mobile",,"46000"),(3,"China Unicom",,"46001"),,(0-4),(0,2)

返回：OK

十、打电话
Demonstration             Syntax                Expect Result

Make a voice call ATD6241xxxx;    OK  MS makes a voice call

Hang up a call       ATH                         OK  Call dropped

问题解决
采用sim300发送短信时采用下面的格式

AT+CMGF=1  设置文本格式

AT+CMGS=”13245678912” 注意这块一定要加上双引号。否则返回ERROR

另外如果发送不出去，有可能是短信中心号码设置的不正确。

完整的程序
// this is a test about GPRS

#include <stdio.h>

#include <string.h>

#include <stdlib.h>

#include <fcntl.h> // open() close()

#include <unistd.h>    // read() write()

#include <termios.h> // set baud rate

#include <fcntl.h>

#include <sys/select.h>

#include <sys/time.h>

#include <sys/types.h>

#define FUNC_RUN          0

#define FUNC_NOT_RUN       1

#define SIMPLE_TEST             1

#define READ_SIM_CARD_ID 2

#define GSM_GPRS_SIGNAL    3

#define MAKE_A_CALL          4

#define WAIT_A_CALL          5

#define SHORT_MESSAGE             6

#define POWER_MANAGE             7

#define FUNC_QUIT       8

#define SEND_SHORT_MESSAGE          1

#define READ_SHORT_MESSAGE          2

#define CONFIG_SHORT_MESSAGE_ENV       3

#define QUIT_SHORT_MESSAGE          4

#define DEVICE_TTYS "/dev/ttySAC1"

#define MAX_LEN_OF_SHORT_MESSAGE 140

#define RECEIVE_BUF_WAIT_1S 1

#define RECEIVE_BUF_WAIT_2S 2

#define RECEIVE_BUF_WAIT_3S 3

#define RECEIVE_BUF_WAIT_4S 4

#define RECEIVE_BUF_WAIT_5S 5

#define VERSION       "YHPDA_GSM_1.0.0"

void showversion(void)

{

      printf("*********************************************\n");

      printf("\t %s \t\n", VERSION);

      printf("*********************************************\n\n");

}

//------------------------------------- read datas from GSM/GPRS --------------------------------------------

// succese return 1

// error return 0

int read_GSM_GPRS_datas(int fd, char *rcv_buf,int rcv_wait)

{

   int retval;

   fd_set RFds;

   struct timeval tv;

   int ret,pos;

   tv.tv_sec = rcv_wait;    // wait 2.5s

      tv.tv_usec = 0;

   pos = 0; // point to rceeive buf



   while (1)

   {

            FD_ZERO(&rfds);

            FD_SET(fd, &rfds);

            retval = select(fd+1 , &rfds, NULL, NULL, &tv);

            if (retval == -1)

            {

                     perror("select()");

                     break;

            }

            else if (retval)

            {// pan duan shi fou hai you shu ju

                     ret = read(fd, rcv_buf+pos, 2048);

                     pos += ret;

                     if (rcv_buf[pos-2] == '\r' && rcv_buf[pos-1] == '\n')

                  {

                              FD_ZERO(&rfds);

                              FD_SET(fd, &rfds);

                              retval = select(fd+1 , &rfds, NULL, NULL, &tv);

                              if (!retval) break;// no datas, break

                     }

            }

            else

            {

                     printf("No data\n");

                     break;

            }

   }

   return 1;

} // end read_GSM_GPRS_datas

//------------------------------------- send cmd ------------------------------------------------------------

// succese return 1

// error return 0

int send_GSM_GPRS_cmd(int fd, char *send_buf)

{

   ssize_t ret;



   ret = write(fd,send_buf,strlen(send_buf));

   if (ret == -1)

      {

            printf ("write device %s error\n", DEVICE_TTYS);

            return -1;

      }

   return 1;

} // end send_GSM_GPRS_cmd

//------------------------------------- send cmd and read back result ---------------------------------------

void GSM_GPRS_send_cmd_read_result(int fd, char *send_buf, int rcv_wait)

{

      char rcv_buf[2048];

   if((send_buf==NULL) || (send_GSM_GPRS_cmd(fd,send_buf)))

   {    // send success , then read

            bzero(rcv_buf,sizeof(rcv_buf));

            if (read_GSM_GPRS_datas(fd,rcv_buf,rcv_wait))

            {

                     printf ("%s\n",rcv_buf);

            }

            else

            {

                     printf ("read error\n");

            }

   }

   else

   {

            printf("write error\n");

   }

} // end GSM_GPRS_send_cmd_read_result

//------------------------------------- send cmd : "at" to GSM/GPRS MODEM -----------------------------------

void GSM_simple_test(int fd)

{

   char *send_buf="at\r";



   GSM_GPRS_send_cmd_read_result(fd,send_buf,RECEIVE_BUF_WAIT_1S);

} // end GSM_simple_test

//------------------------------------- send cmd : "at+ccid" to GSM/GPRS MODEM ------------------------------

void GSM_read_sim_card_id(int fd)

{

      char *send_buf="at+ccid\r";

   GSM_GPRS_send_cmd_read_result(fd,send_buf,RECEIVE_BUF_WAIT_1S);

} // end GSM_read_sim_card_id

//------------------------------------- send cmd : "at+ccid" to GSM/GPRS MODEM ------------------------------

void GSM_gprs_signal(int fd)

{

      char *send_buf="at+creg?\r";

   GSM_GPRS_send_cmd_read_result(fd,send_buf,RECEIVE_BUF_WAIT_1S);

      send_buf="at+cgreg?\r";

   GSM_GPRS_send_cmd_read_result(fd,send_buf,RECEIVE_BUF_WAIT_1S);

      send_buf="at+csq\r";

   GSM_GPRS_send_cmd_read_result(fd,send_buf,RECEIVE_BUF_WAIT_1S);

      send_buf="at+cops?\r";

   GSM_GPRS_send_cmd_read_result(fd,send_buf,RECEIVE_BUF_WAIT_1S);

} // end GSM_read_sim_card_id

//------------------------------------- send cmd : "atd<tel_num>;" to GSM/GPRS MODEM ------------------------

//------------------------------------- finish call, send cmd:  "ath" to GSM MODEM --------------------------

void GSM_call(int fd)

{

   char send_buf[17];

   char *send_cmd_ath = "ath\r";

   int i;

      // input telephone number

      bzero(send_buf,sizeof(send_buf));



      send_buf[0]='a';

      send_buf[1]='t';

      send_buf[2]='d';

   send_buf[16] = '\0';

      printf("please input telephone number:");

      i = 3;

      while (1)

      {

            send_buf=getchar();

            if (send_buf=='\n') break;

            i++;

      }

      send_buf=';';

      send_buf[i+1]='\r';

   // end input telphone number

   // send cmd

   GSM_GPRS_send_cmd_read_result(fd,send_buf,RECEIVE_BUF_WAIT_1S);

      //quit call

      printf("press ENTER for quit:");

      getchar();

      // send cmd

   GSM_GPRS_send_cmd_read_result(fd,send_cmd_ath,RECEIVE_BUF_WAIT_1S);



} // end GSM_call

//------------------------------------- wait for GSM/GPRS call signal ---------------------------------------

void GSM_wait_call(int fd)

{

   char rcv_buf[2048];

   char *send_cmd_ath = "ath\r";

      int wait_RING;

      wait_RING = 10;

      while (wait_RING!=0)

      {

            bzero(rcv_buf,sizeof(rcv_buf));

            if (read_GSM_GPRS_datas(fd,rcv_buf,RECEIVE_BUF_WAIT_1S))

            {

                     printf ("%s\n",rcv_buf);

            }

            else

            {

                     printf ("read error\n");

            }

            wait_RING--;

      }



   GSM_GPRS_send_cmd_read_result(fd,send_cmd_ath,RECEIVE_BUF_WAIT_1S);

      printf("quit wait_call\n");

} // end GSM_wait_call

//------------------------------------- GSM/GPRS Config short message env -----------------------------------

void GSM_Power_Manage(int fd)

{

   char *send_buf="AT+CPOWD\r";// power off

   GSM_GPRS_send_cmd_read_result(fd,send_buf,RECEIVE_BUF_WAIT_1S);

} // end GSM_Conf_Message

//------------------------------------- GSM/GPRS send short message -----------------------------------------

void GSM_Send_Message(int fd)

{

      char cmd_buf[23];

      char short_message_buf[MAX_LEN_OF_SHORT_MESSAGE];

      int  i;

      char rcv_buf;

      bzero(cmd_buf,sizeof(cmd_buf));

      bzero(short_message_buf,sizeof(short_message_buf));

      printf ("send short message:\n");

      cmd_buf[0]='a';

      cmd_buf[1]='t';

      cmd_buf[2]='+';

      cmd_buf[3]='c';

      cmd_buf[4]='m';

      cmd_buf[5]='g';

      cmd_buf[6]='s';

      cmd_buf[7]='=';

      cmd_buf[8]='"';

      printf ("please input telephone number:");

      i = 9;

      while (1)

      {

            cmd_buf=getchar();

            if (cmd_buf=='\n') break;

            i++;

      }

   cmd_buf='"';

      cmd_buf[i+1]='\r';

   cmd_buf[i+2]='\0';

      // send cmd :  at+cmgs="(telephone number)"

   GSM_GPRS_send_cmd_read_result(fd,cmd_buf,RECEIVE_BUF_WAIT_1S);



   // input short message

      printf("please input short message:");

      i = 0;

      while(i < MAX_LEN_OF_SHORT_MESSAGE-2)

      {

            short_message_buf = getchar();

            if (short_message_buf=='\n') break;

            i++;

      }

      short_message_buf = 0x1A;

      short_message_buf[i+1] = '\r';

   short_message_buf[i+2] = '\0';

      // send short message

   GSM_GPRS_send_cmd_read_result(fd, short_message_buf,RECEIVE_BUF_WAIT_4S);

      printf("\nend send short message\n");

} // end GSM_Send_Message

//------------------------------------- GSM/GPRS read all short message -------------------------------------

void GSM_Read_Message(int fd)

{

   char *send_buf="at+cmgl=\"ALL\"\r";

   char rcv_buf[2048];

      GSM_GPRS_send_cmd_read_result(fd,send_buf,RECEIVE_BUF_WAIT_3S);

   printf("end read all short message\n");

} // end GSM_Read_Message

//------------------------------------- GSM/GPRS Config short message env -----------------------------------

void GSM_Conf_Message(int fd)

{

   char *send_buf="at+cmgf=1\r";

   char *send_center_buf="at+csca=\"+8613800571500\"\r";

   GSM_GPRS_send_cmd_read_result(fd,send_buf,RECEIVE_BUF_WAIT_1S);

      // set short message center number

      GSM_GPRS_send_cmd_read_result(fd,send_center_buf,RECEIVE_BUF_WAIT_1S);

      printf("end config short message env\n");

} // end GSM_Conf_Message

//------------------------------------- GSM/GPRS short message ----------------------------------------------

void GSM_short_mesg(int fd)

{

      int flag_sm_run, flag_sm_select;

      flag_sm_run = FUNC_RUN;

      while (flag_sm_run == FUNC_RUN)

      {

            printf ("\n Select:\n");

            printf ("1 : Send short message \n");

            printf ("2 : Read all short message \n");

            printf ("3 : Config short message env\n");

            printf ("4 : quit\n");

            printf (">");

            scanf("%d",&flag_sm_select);

            getchar();

            // temp

   //    printf ("input select:%d\n",flag_sm_select);

            // end temp

            switch (flag_sm_select)

            {

                     case SEND_SHORT_MESSAGE       :    { GSM_Send_Message(fd);       break; }

                     case READ_SHORT_MESSAGE       :    { GSM_Read_Message(fd);       break; }

                     case CONFIG_SHORT_MESSAGE_ENV :    { GSM_Conf_Message(fd);       break; }

                     case QUIT_SHORT_MESSAGE       :    { flag_sm_run = FUNC_NOT_RUN;    break; }

                     default :

                              {

                                    printf("please input your select use 1 to 3\n");

                              }

            }

      }

      printf ("\n");

} // end GSM_send_mesg

//------------------------------------- print ---------------------------------------------------------------

void print_prompt(void)

{

      printf ("Select what you want to do:\n");

      printf ("1 : Simple Test\n");

      printf ("2 : Read SIM CARD ID\n");

      printf ("3 : Test GSM/GPRS signal\n");

      printf ("4 : Make A Call\n");

      printf ("5 : Wait A Call\n");

      printf ("6 : Short message\n");

      printf ("7 : Power manage\n");

      printf ("8 : Quit\n");

      printf (">");

} // end print_prompt

//------------------------------------- Control GSM/GPRS MODULE ---------------------------------------------

void func_GSM(int fd)

{

      int flag_func_run;

      int flag_select_func;

      ssize_t ret;

      flag_func_run = FUNC_RUN;

      while (flag_func_run == FUNC_RUN)

      {

            print_prompt();                   // print select functions

            scanf("%d",&flag_select_func); // user input select

            getchar();

            switch(flag_select_func)

            {

                     case SIMPLE_TEST       : {GSM_simple_test(fd);       break;}

                     case READ_SIM_CARD_ID : {GSM_read_sim_card_id(fd); break;}

                     case GSM_GPRS_SIGNAL : {GSM_gprs_signal(fd);       break;}

                     case MAKE_A_CALL       : {GSM_call(fd);             break;}

                     case WAIT_A_CALL       : {GSM_wait_call(fd);          break;}

                     case SHORT_MESSAGE    : {GSM_short_mesg(fd);       break;}

                     case POWER_MANAGE    : {GSM_Power_Manage(fd);       break;}

                     case FUNC_QUIT       :

                                             {

                                                      flag_func_run = FUNC_NOT_RUN;

                                                      printf("Quit GSM/GPRS function.  byebye\n");

                                                      break;

                                             }

                     default :

                     {

                              printf("please input your select use 1 to 7\n");

                     }

            }

      }

}// end func_GPRS

//------------------------------------- init seriel port  ---------------------------------------------------

void init_ttyS(int fd)

{

   struct termios options;

   bzero(&options, sizeof(options));    // clear options

   cfsetispeed(&options,B115200);          // setup baud rate

   cfsetospeed(&options,B115200);

   options.c_cflag |= (CS8 | CREAD);

   options.c_iflag = IGNPAR;

   tcflush(fd, TCIFLUSH);

   tcsetattr(fd, TCSANOW, &options);

}//end init_ttyS

//------------------------------------- main ----------------------------------------------------------------

int main(void)

{

      int fd;

   showversion();

      printf("\nGSM/GPRS TESTS\n\n");

      // open seriel port

      fd = open(DEVICE_TTYS, O_RDWR);

      if (fd == -1)

      {

            printf("open device %s error\n",DEVICE_TTYS);

      }

      else

      {

            init_ttyS(fd);  // init device

            func_GSM(fd);    // GSM/GPRS functions



            // close ttyS0

            if (close(fd)!=0) printf("close device %s error",DEVICE_TTYS);

      }

      return 0;

}// end main

该程序目前的问题如下，在接受短信的时候无法显示短信的内容，而只是显示一个“~p”，谁有这个问题的解决方法，欢迎与我探讨。

ExxNEN · 发表于 2020-3-27 17:55

GPRS模块SIM300的使用

帐号		自动登录	找回密码
密码			注册

GPRS模块SIM300的使用

EDA365欢迎您登录！

浏览过的版块

推荐内容 /1