死铜在哪里啊？？

jackyard

我画了一个四层的板，中间两层中，其中一层是地，一层是电源，我把电源分切了好几块，为什么在电气检测中老是出现面的问题：
4 }8 F1 G6 h5 S( ^

Un-Routed Net Constraint ( (All) )

Isolated copper: Split Plane (GND_SIGNAL) on GND02. Dead copper detected. Copper area is : 2.4E2 sq. mils ; u0 `- P6 [. |2 s: J! Z

Isolated copper: Split Plane (GND_SIGNAL) on GND02. Dead copper detected. Copper area is : 1.7E2 sq. mils

Isolated copper: Split Plane (GND_SIGNAL) on GND02. Dead copper detected. Copper area is : 1.2E2 sq. mils

Isolated copper: Split Plane (GND_SIGNAL) on GND02. Dead copper detected. Copper area is : 1.1E2 sq. mils 9 l  \3 i- A4 }) n+ X3 e! t) a

Isolated copper: Split Plane (3V3_VDD2) on PWR03. Copper island connected to pads/vias detected. Copper area is : 1.3E3 sq. mils ! L5 S9 |! S" G& z' a  p

Isolated copper: Split Plane (1V0_TXRX) on PWR03. Copper island connected to pads/vias detected. Copper area is : 1.1E3 sq. mils

Isolated copper: Split Plane (1_2V_DVDD) on PWR03. Copper island connected to pads/vias detected. Copper area is : 2.1E3 sq. mils

Isolated copper: Split Plane (1V0) on PWR03. Copper island connected to pads/vias detected. Copper area is : 9E2 sq. mils ) a7 G7 C% p! k4 x1 k( Z

Isolated copper: Split Plane (3V3) on PWR03. Dead copper detected. Copper area is : 1.5E4 sq. mils 0 v2 T# Q3 i9 H6 J- u9 a

Isolated copper: Split Plane (3V3) on PWR03. Copper island connected to pads/vias detected. Copper area is : 5.3E3 sq. mils / g4 P* P. l8 e6 d4 X5 b

Isolated copper: Split Plane (3V3) on PWR03. Copper island connected to pads/vias detected. Copper area is : 1.2E3 sq. mils ( x; ~, @9 S' B+ ~0 X4 m$ J3 z

Isolated copper: Split Plane (3V3) on PWR03. Copper island connected to pads/vias detected. Copper area is : 1.2E3 sq. mils / B: v2 s  [9 s# l2 j4 P& U

Isolated copper: Split Plane (3V3) on PWR03. Copper island connected to pads/vias detected. Copper area is : 9.4E2 sq. mils

Isolated copper: Split Plane (3V3) on PWR03. Dead copper detected. Copper area is : 9.1E2 sq. mils

Isolated copper: Split Plane (3V3) on PWR03. Copper island connected to pads/vias detected. Copper area is : 7.9E2 sq. mils

Isolated copper: Split Plane (3V3) on PWR03. Dead copper detected. Copper area is : 4.4E2 sq. mils

Isolated copper: Split Plane (3V3) on PWR03. Dead copper detected. Copper area is : 1.7E2 sq. mils

而在PCB中也看不到绿色的出错指示，请高人指点一下。

SSDMA

via太多，太密了。内电层的死铜，可以通过调整via的位置或其他方式去除。
* A9 C% j% }: y" J, m6 U表层铺铜的设置是没有用的

kgsz

覆铜的时候 不是有 除去死铜这个选项么？

rongsun1123

二楼的看法是对的。

jackyard

回复 SSDMA 的帖子
( `' F! h) q: O' a. g
你说的对，后来在rule里改了就好了。哈哈

sunlin0112

恩 不错

zdh_054

呵呵 楼主估计也困惑好久吧 以前我也碰到过，找了好久才发现的。其实AD中的错误是有颜色标记的 就看眼力怎么样了

stupidboy

重新生成一下内电层就可以了

dashuszhl055

你好 这个主题的问题你是怎么解决的 我也是遇到一样的问题 画的是六层 电源层和地层 你是怎么通过修改规则来去掉那些提示检测的 谢谢了~

wrh

可以设一个room区域规则，即在孔比较密集的地方画好room区域，把区域内的内层隔离环改小

dashuszhl055

wrh 发表于 2012-12-17 16:30
可以设一个room区域规则，即在孔比较密集的地方画好room区域，把区域内的内层隔离环改小

- Y, p, Q+ e, l挺不错的 谢谢~

糖人

SSDMA 发表于 2011-3-31 14:16
4 d4 F- }- R4 f2 S) G6 e; jvia太多，太密了。内电层的死铜，可以通过调整via的位置或其他方式去除。
表层铺铜的设置是没有用的

有效的方法是啥啊
; g8 b- w) r' h/ |/ ^