EDA365电子论坛网
标题:
orcad library builder 16.6.62创建PCBfootprint库导出后没管焊盘管脚？
[打印本页]
作者:
ylgw811002
时间:
2018-3-4 23:53
标题:
orcad library builder 16.6.62创建PCBfootprint库导出后没管焊盘管脚？
在创建PCB footprint库导出时，没有焊盘不知道什么原因？如图所示，并出现下面提示：E- (SPMHAP-2): No padstack specified.E- (SPMHAP-3): Problem loading 'c45.pad'.
; [; f) \- T! ~# \% F! @
) L5 ?; Z8 D; E; c, S
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
2 Y# B' b3 P1 Y9 F. j C s
E- (SPMHAP-2): No padstack specified.
4 A) [6 B5 @6 ~& o, J0 r% D
- [& k5 ]2 ?. ~( [7 b" C
E- (SPMHAP-3): Problem loading 'c45.pad'.
: |7 l' m) @9 ]' K
7 h* E0 [2 a4 r+ V
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
4 Q/ O# z' }# Y
E- (SPMHAP-2): No padstack specified.
2 p3 \5 F$ c$ f" u+ I1 V
1 M, }, r. B% r
E- (SPMHAP-3): Problem loading 'c45.pad'.
1 B) l# ~! d% X E& V2 O
' c+ ^5 {% f* L$ ]( y- X! E
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
8 w/ I$ p2 s! f" f I4 E
4 k- ?" S1 z6 I* Q. k6 O5 {
E- (SPMHAP-2): No padstack specified.
! y3 Z/ p( v. P* A
9 Q& ?$ R# e, }/ a0 Q
E- (SPMHAP-3): Problem loading 'c45.pad'.
+ k5 B: [8 `+ y# _" `
1 `0 r2 Z0 N7 ~0 q4 Y* k' h% Y7 X$ d
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
' s6 u+ x# H' q! d) U
E- (SPMHAP-2): No padstack specified.
1 n/ b, r. c$ B9 y1 A7 E2 }7 x
1 \/ Y% {( y5 B5 r' R p
E- (SPMHAP-3): Problem loading 'c45.pad'.
- |& l) _" D0 V; R/ |
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
9 C$ x% y# Z$ Z' _2 x
& m# f1 Q: g( T3 ^/ d- h M1 d; a
E- (SPMHAP-2): No padstack specified.
9 Y8 r5 K6 U# A2 _# F
+ X y" U s! ~$ _$ v' c2 Z0 X4 x
E- (SPMHAP-3): Problem loading 'c45.pad'.
: F7 H8 C6 t2 ?6 u3 Q5 i7 W
# y# j) C% W1 x e
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
; S2 _5 t8 ^1 F4 I P2 I2 e) O
7 K2 \4 U7 D$ W8 i
E- (SPMHAP-2): No padstack specified.
! W+ r! j/ e! b- [& b
8 L L9 C( k7 h& \5 Z, K( r" }$ b
E- (SPMHAP-3): Problem loading 'c45.pad'.
* p) ]! r* U. z2 x( k1 H
, S* z+ \/ W+ L. ~# L
E- (SPMHA1-161): Cannot open the design database file ... run standalone dbdoctor on the file.
- T) h k3 |# I, z) Y0 f6 K! t4 K/ @
作者:
ylgw811002
时间:
2018-3-5 00:10
2 、在allegro中，软件默认的焊盘那些路径不能删除。即padpath路径下的$padpath不能给删除；出现此问题只和padpath路径有关系，和psmpath路径没有关系，路径设置如下（可以在原来的基础上添加其它路径）： 1
3 @$ J, j5 @8 Z, h
作者:
yangjinxing521
时间:
2018-3-5 08:46
正解
作者:
TobyTao_Zhang
时间:
2018-3-5 11:08
export libraries 之前先把要导出到 的folder 路径也加到padpath 里面
作者:
ylgw811002
时间:
2018-3-5 21:12
为啥通孔类的没有焊盘了 擦 能否给个详细的教程
作者:
ylgw811002
时间:
2018-3-6 16:46
能不能自动 DB doctor 生成的焊盘总是有问题
作者:
ylgw811002
时间:
2018-3-14 22:50
能有大神给个解决的办法了 多谢了
作者:
liangping367
时间:
2018-3-16 22:33
你能够导出OLB文件吗
- }( }# d- l$ Z: ]1 |
作者:
风凌天下
时间:
2018-8-2 16:30
我的也是，问题我之前版本没问题，后面卸载重新装了就不能生成封装了
欢迎光临 EDA365电子论坛网 (https://bbs.eda365.com/)
Powered by Discuz! X3.2
